From Concept
To Completion
Engineering, procurement and construction for refineries, offshore platforms and process plants — static equipment, rotating equipment and control systems delivered to API, ASME and TEMA codes.
To establish a name and lead the international market in engineering business and EPC projects — by achieving 100% client satisfaction.
One Contractor
Full Lifecycle
A single point of responsibility from the first simulation run to mechanical completion and handover.
Engineering
Process simulation, FEED and detailed design across process, mechanical, piping, electrical and instrumentation disciplines.
Procurement
Vendor qualification, technical bid evaluation, expediting and inspection for equipment and bulk materials.
Construction
Fabrication, installation, pre-commissioning and commissioning at site with QA/QC and HSE control.
Management
Project controls, scheduling, cost and interface management from contract award to handover.
Six Stages
One Handover
Every project moves through the same gated sequence, with documented deliverables signed off before the next stage begins.
Concept & Feasibility
Site data, design basis and process simulation to confirm the technical case.
→ DESIGN BASISFEED
Front-end engineering: PFDs, P&IDs, plot plans and equipment data sheets.
→ FEED PACKAGEDetailed Engineering
Discipline design, calculations and construction drawings to applicable codes.
→ IFC DRAWINGSProcurement
Vendor enquiries, technical bid evaluation, inspection and expediting.
→ EQUIPMENT AT SITEConstruction
Fabrication, erection and installation under QA/QC and HSE supervision.
→ MECHANICAL COMPLETIONCommissioning
Pre-commissioning, loop checks, start-up support and handover dossiers.
→ PLANT HANDOVERIn-House,
Multi-Discipline
Discipline leads work from a single model and document register, so interfaces are resolved on paper — not at site.
Process
Simulation studies, heat & material balances, PFDs, P&IDs and equipment sizing.
Mechanical — Static
Storage tanks, pressure vessels and heat exchangers to API, ASME and TEMA.
Mechanical — Rotating
Pump selection, compressor packages and skid-mounted equipment.
Piping
Layout, stress analysis and material specification to ASME B31.3.
Instrumentation & Control
DCS and PLC architecture, control valves, flow metering and loop design.
Electrical
Power distribution, motor control and hazardous-area classification.
Built To Code
Design, supply and integration across static, rotating and instrumentation packages. Select an item to view.
Process Simulation Studies
Steady-state and dynamic simulation, heat & material balances and PFD development to size equipment before it is built.
Storage Tanks
Atmospheric welded steel tanks for crude, product and water service — design, fabrication and erection.
Shell & Tube Heat Exchanger
Thermal and mechanical design of shell & tube exchangers for refinery and process duty.
Pressure Vessel
Separators, drums, columns and spheres designed and stamped to ASME Section VIII.
Pumps
Centrifugal process pumps selected against head-flow, efficiency and NPSH curves.
Control Valves
Sizing and selection of globe and rotary control valves with actuator and positioner packages.
DCS System
Distributed control architecture, I/O design, configuration and loop commissioning.
PLC System
PLC-based control and safety logic for packaged units and balance of plant.
Flow Meters
Electromagnetic, Coriolis and differential-pressure metering for custody and process measurement.
Chemical Injection Skids
Skid-mounted dosing packages for corrosion inhibitor, scale and methanol injection.
Upstream To Downstream
Oil Refinery Plants
Control Rooms
Drilling Platforms
Oil Well Pump Jacks
Safe By
Design
Safety and quality are engineered into the design basis, not inspected in at the end.
Before You
Ask
Yes. Clients can engage us for a single stage — a simulation study, FEED, or equipment supply — or for a full lump-sum EPC contract.
Oil and gas upstream and downstream, refineries, offshore facilities and process plants, including utilities and chemical injection systems.
Yes. Our objective is to lead in the international EPC market, and we support projects abroad from our Karachi office.
API, ASME, TEMA, ISA and IEC standards as applicable, or the client's own project specifications where they apply.
Send us your scope or enquiry through the form below. We review it, arrange a technical clarification call and issue a proposal.
Start With
A Conversation
Gulshan-e-Kaneez Fatima,
Sector 16-A, KDA Scheme # 33,
Karachi — Pakistan